Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterFamco Chimney Liner & Rebuild in Evanston: What to Know First
We provide independent Famco chimney liner and rebuild service in Evanston, typically quoting jobs within 48 hours of your call and completing most liner replacements inside a single day. Every Famco job starts with a camera-scan inspection, a written price, and a documented photo record - nothing gets approved without both on the table. If you own a Famco chimney component and need liner work or masonry rebuild, call us at (708) 234-1174 for a free estimate. Corrine Halstead and our crew have inspected stacks across Evanston, including the older masonry near the lakefront historic district where Famco caps and collars from the 2000s are starting to show their age.
How Famco Products Fail - and How We Fix Them
- Famco 304 stainless collars on pre-fab chimneys - the rolled edge traps condensation against the chase cover in Evanston’s freeze-thaw cycles. We’ve pulled dozens of these where the collar rusted through from the underside while the top still looked fine. We cut back to sound metal, seal with a proper storm collar, and document the chase cover condition under Haven Standard Clause 4.
- Famco single-wall galvanized tee connectors in venting systems - these were common on 1990s Evanston townhome installs and fail at the weld seam when used with modern higher-efficiency appliances. The seam opens, flue gases spill into the chase. We replace with an appropriate listed liner system, usually DuraFlex or a quality aftermarket equivalent rated for the actual appliance.
- Famco masonry chimney caps on homes near Lake Michigan - the salt-laden onshore air accelerates galvanic corrosion where the cap meets the flue tile. Spalling concrete follows within two seasons. We assess whether the crown can be resurfaced with HeatShield or if the cap and upper courses need rebuild, and we show you the camera footage of the flue interior before recommending either.
- Famco flexible liner kits installed without proper support - the sag at the first offset collects acidic condensate, thinning the wall from the inside. On Evanston’s older two-story homes with tight chimney throats, this is almost predictable. We pull the compromised section, measure the actual offset angle, and reinstall with proper support spacing per the liner manufacturer’s tables - not the shortcut the last installer used.
- Famco top-sealing dampers retrofitted to damaged flue tiles - the damper frame seals against the flue wall, but if the tile is cracked or missing a corner, you’re sealing a broken system. We run the camera to map every defect, then quote liner replacement or flue tile repair based on what we found, not what we hope will work.
Our Famco Chimney Liner & Rebuild Process
- 1
Call and schedule - a live person answers, 24/7. We book your NFPA 211 Level 2 inspection, usually within a week in Evanston.
- 2
Camera-scan inspection - our tech runs a chimney camera the full flue length, records footage, and measures liner diameter, wall thickness, and offset angles. You watch the screen. The camera doesn’t negotiate - and neither does creosote.
- 3
Written diagnosis and price - we deliver a written scope, written price, and written warranty before any work starts. Haven Standard Clause 1. If you have a competitor’s written estimate, we’ll give you a free second opinion.
- 4
Parts selection - Famco OEM where it matters for fit, quality aftermarket (DuraFlex, HeatShield, Gelco, Olympia Chimney) where specifications match or exceed. We source through Haven’s buying network to keep your price honest.
- 5
Repair and test - liner pull and replacement, or masonry rebuild to specification. We pressure-test or smoke-test as appropriate, then run the camera again to document the finished flue.
- 6
Documentation and guarantee - you receive photos, camera footage, readings, and a written warranty. Backed by our 365-Day Done Right Promise. If it’s not done right, we make it right.
Before
AfterWhat Famco Chimney Liner & Rebuild Costs in Evanston
| Service | Typical Range |
|---|---|
| Famco liner inspection with camera scan | $199-$289 |
| Partial liner repair (localized section) | $850-$1,400 |
| Full stainless steel liner replacement (single flue) | $2,800-$4,500 |
| Flexible liner with offset correction | $3,200-$5,100 |
| Upper chimney rebuild (crown, cap, 4-6 courses) | $2,400-$4,200 |
| Full chimney rebuild with new liner | $8,500-$14,000 |
Price moves with flue height, access difficulty, and whether we find hidden damage the camera reveals - which is exactly why we run the camera first. Evanston’s tighter lot lines and older homes often mean scaffolding or interior access, both of which we quote explicitly. Call (708) 234-1174 for your exact written estimate. Estimates are free.
Why Evanston Homeowners Call Level Two Chimney Evanston for Famco Work
We’ve completed more than 38,000 chimney inspections and cleanings since 2009, every one with a written price before work started and a documented record when done. Our background-checked, uniformed technicians are assigned by name - you’ll get a text when yours is on the way. We know Famco’s product lines because we’ve pulled and replaced them across Evanston’s housing stock, from the 1920s masonry near Central Street to the 1980s townhomes off Dodge. And we’re not locked to one supplier: when Famco OEM isn’t the right fit, we specify DuraFlex, HeatShield, Gelco, or Olympia Chimney based on what your flue actually needs. As an independent Famco service provider, we have no manufacturer quota to meet - only the Haven Standard to keep.
FAQs
Most Famco warranties on original components expired years ago, and manufacturer warranties typically don’t cover labor or subsequent modifications anyway. Our repairs use listed, compatible materials and don’t create code violations. If you have active warranty paperwork, bring it - we’ll review it before quoting. Call (708) 234-1174 and we’ll sort out what’s actually covered.
Yes. Famco produced standard-diameter components for decades, and we source direct-fit replacements through Haven’s buying network. Where Famco-specific parts are discontinued, we specify aftermarket equivalents that meet or exceed UL 1777 listing. We never guess on compatibility - we measure your flue and match the spec sheet.
The camera decides. Hairline cracks and isolated spalling often justify liner repair or resurfacing. Multiple fractures, missing tiles, or visible gaps between flue sections mean replacement. We show you the footage, explain the failure mode, and quote both options when both are safe. No work starts without your written approval.
Most single-flue liner replacements in Evanston finish in one day. Full rebuilds with liner replacement take two to four days depending on weather and masonry cure requirements. We book with realistic timelines - no urgency theatre, no phantom scheduling pressure.
Damaged liners let flue gases, including carbon monoxide, leak into wall cavities and living spaces. In Evanston’s older homes with balloon framing, that migration happens fast. Creosote can also reach combustible framing. The risk is real and specific, not abstract. Call (708) 234-1174 for a camera inspection - we’ll show you exactly what your flue looks like today.
Written by Corrine Halstead, Owner, Level Two Chimney Evanston at Level Two Chimney Evanston, serving Evanston and nearby areas.