Olympia Chimney Crown Repair Nationwide

Olympia Chimney Crown Repair: The Evanston Owner’s Guide

Olympia Chimney crown repair in Evanston typically runs $680-$1,450 installed, depending on whether we’re sealing hairline cracks or pouring a new concrete crown with integrated drip edge. We stock Olympia Chimney-compatible crown sealants, stainless steel drip edges, and forming materials on every truck, and most jobs are completed in a single visit. Most Evanston homeowners discover the problem during a routine sweep or after spotting water stains on the ceiling near the fireplace - by then, freeze-thaw damage has usually progressed past a simple seal.

Call (708) 234-1174

Which Olympia Chimney Models This Applies To

Olympia Chimney manufactures several liner and venting product lines, but the crown itself is the masonry cap that terminates the chimney structure above the flue. If your home in Evanston has an Olympia Chimney stainless steel liner or factory-built metal chimney, the crown we’re discussing is the masonry or concrete cap that seals the top of your brick chase - not the Olympia Chimney product itself. That distinction matters because we’ve seen homeowners order Olympia Chimney “crowns” online only to receive chase covers meant for factory-built installations, which won’t fit a traditional masonry stack.

To identify what you actually need, we measure the chimney’s outside dimensions at the top course of brick, count the flue tile openings, and check whether the existing crown is a cast-in-place concrete slab or a pre-formed cement board. Olympia Chimney-compatible crown repairs in Evanston typically involve one of three scenarios: sealing a poured concrete crown with minor cracking, replacing a deteriorated crown with new concrete and stainless steel reinforcement, or installing a proper concrete crown where a previous installer used mortar alone. We source forming materials and stainless drip edges through our Haven buying network, which includes Olympia Chimney, DuraFlex, HeatShield, and Gelco suppliers.

Level Two Chimney Evanston is an independent service provider with no affiliation to Olympia Chimney Corporation.

Signs Your Olympia Chimney Crown Repair Is Failing

• Hairline cracks running across the crown surface. These form when the concrete crown lacks an expansion joint or was poured without reinforcement. In Evanston, water enters these cracks in October, freezes by November, and widens them into structural gaps by spring.
• Chunks of concrete missing from the crown edge. Called spalling, this happens when the crown mix was too wet at pour or the drip edge was omitted, letting water run back under the crown and saturate the brick below.
• Water stains on the ceiling near the chimney breast. By the time interior staining appears, water has already migrated through the crown, saturated the chimney structure, and found a path into your living space - often requiring more than crown work alone.
• White powder forming on the crown or brick faces. Efflorescence is salt left behind as water evaporates; it means moisture is moving through the masonry continuously, and the crown’s waterproofing has failed.
• The crown slopes toward the flue instead of away from it. A properly poured crown needs minimum 3/4-inch per foot slope to shed water. Flat or reverse-sloped crowns pool water and accelerate deterioration, especially under Evanston’s lake-effect snow loads.

Before

After

Replacement Cost & What’s Included

What drives the range: crown size (a 36-by-48-inch crown takes more material than a 24-by-24), number of flue openings requiring cutouts, whether the top course of brick needs rebuilding first, and accessibility - Evanston’s tighter lakefront lots with mature trees sometimes require ladder work where bucket trucks won’t fit. Every price is written before work starts, under Haven Standard Clause 1. The 365-Day Done Right Promise applies to all crown work, and your photo record is archived under Clause 4.

DIY or Call Us?

Here’s what you can safely check yourself: from the ground with binoculars, look for the crack patterns and spalling described above. If you have safe roof access and a stable ladder, measure the crown’s slope with a level - it should pitch away from the flue. Document what you see with photos.

Here’s where DIY goes wrong: crown repair requires forming, concrete mixing to the correct slump, and proper cure time in weather above 40 degrees. We’ve been called to Evanston homes where a homeowner’s hardware-store sealant trapped water inside, accelerating brick damage, or where a self-poured crown sloped the wrong direction and funneled water directly into the flue. Worse, working at chimney height on a pitched roof is genuinely dangerous - falls from roof edges account for a significant share of serious home improvement injuries.

We bring the forms, the reinforced mix rated for freeze-thaw cycling, and the stainless drip edges sized to your chimney. Call (708) 234-1174 and we’ll quote it in writing before anyone climbs.

FAQs